Skip to header Skip to main navigation Skip to main content Skip to footer

User account menu

  • Log in
Home
Workshop Calculation and Science
ITI Workshop Calculation & Science – Complete Study Guide

Main navigation

  • Home
  • Question Paper
  • Syllabus
  • Video
  • Employability Skills (opens in new tab)
  • Engineering Drawing (opens in new tab)
  • Hunnarbaaz (opens in new tab)
  • ITI Tools (opens in new tab)
  • Syllabus (opens in new tab)

Workshop Calculation Semester 2 July 2018

  • Read more about Workshop Calculation Semester 2 July 2018

Choose the correct answer.

1.Tan45°, cot 45°=

a. 1
b.1/2
c.1/√2
d. 0

2. Circumference of a circle is given by______
a. πD 

b. 2r
c. Both (a) & (b)
d. Neither a nor b

3.The area of a parallelogram is 72 cm and its altitude is twice the corresponding base. Then
the length of the base is_____.
a. 12 cm
b. 9 cm
C. 6 cm
d. 3 cm

4.The ratio of area of a circle to the area of semi-circle is-
a. 1:2
b .2: 1
c..4:1
d.1:4

Workshop Calculation Semester 2 July 2017

  • Read more about Workshop Calculation Semester 2 July 2017

PART- A (WORKSHOP CALCULATION & SCIENCE)
(75)
Choose the correct answer:
1.If the area of square plate is 2025 mm2, then find the side-
a. 65 mm
b. 55 mm
c. 45mm
d. 35 mm

Fundamental and Derived Units F.P.S, C.G.S, M.K.S and SI Units

By Anand | 12:55 AM MST, Thu January 01, 2026
  • F.P.S system is the British system in which the basic units of length, mass and time are foot, pound and second respectively.
  • C.G.S system is the metric system in which the basic units of length, mass and time are centimeter, gram and seconds respectively.
  • M.K.S system is another metric system in which the basic units of length, mass and time are metre, kilogram and second respectively
  • S.I. units are referred to as Systems International units which is again of metric and the basic units, their names and symbols are as follows.
  • Read more about Fundamental and Derived Units F.P.S, C.G.S, M.K.S and SI Units
  • Log in to post comments

Classification of Unit System

By Anand | 12:56 AM MST, Sat November 15, 2025

Necessity
All physical quantities are to be measured in terms of standard quantities.

Unit
A unit is defined as a standard or fixed quantity of one kind
used to measure other quantities of the same kind.

Classification
Fundamental units and derived units are the two classifications.

Fundamental units
Units of basic quantities of length, mass and time.

  • Read more about Classification of Unit System
  • Log in to post comments

Monthly test (November-2015)

  • Read more about Monthly test (November-2015)

WORKSHOP CALCULATION AND SCIENCE
Monthly test (November-2015)
Time: 1:30 hours
Total marks: 50
1. A piece of alloy weighing 80grams consists of 60grams of copper and the remaining is zinc. The ratio of
copper to zinc is...
a) 3:2

b) 3:4

c) 3:1

d) 3:3

2. 1200kg of mild steel 25% of metal is cul and removed. The net weight of remaining
a) 600kg

b) 700kg

c) 900kg

d) 1000kg

Workshop Calculation Semester 1 Jan 2018

  • Read more about Workshop Calculation Semester 1 Jan 2018

Choose the correct answers:
 1 .0.2 Kg =
a) 200 gram
b) 20 gram
c) 2 gram
d) None of these

2.The number1/2 x 1/2 ÷ 1/3 is equal to -

a) 1

b) 1/2

c) 2

d) 1/4
  

3.One gallon is equal to__________ litres.
a) 4.1 litre
b) 4.24 litre
c) 4.50 litre
d) 4.54 litre

4.Reciprocal of -5 is-
a) -1/5

b) 1/5

c) +5

d) 1

5. Sum of Number 7/12 & -5/16 is equal to -
a) -7/48

b) -11/30

c) 13/48

d) 1/3

Workshop Calculation & Science Sem 2 Jan 2018

  • Read more about Workshop Calculation & Science Sem 2 Jan 2018

WORKSHOP CALCULATION & SCIENCE SEM 2 JAN 2018

1. Which one of the following is equal to am X an
  m n mn m/n
b) a

Mechanical equivalent of heat is ........
a) 4200 J/kgoc
b) 42.00 J/kgoc 
c) 420.0 J/kgoc
d) 4.20 J/kgoc

Basic unit of current is
a) Micro amps
b) Millie amps
c) Amps 
d) Kilo amps

Find the value of y if (3/5) .....(15/5y) = 3/4
b) -98 c) -100 d) -102

Workshop Calculation Semester 3 July 2018

  • Read more about Workshop Calculation Semester 3 July 2018

MARKS: 75
Note: Attempt All the questions.
All questions carry equal marks.
Choose the correct answers:
1.Which of the following property is affected by heat treatment?
(a) Hardness
(b) Strength
(c) Ductility
(d) All of these


2. Annealing involves heating the component to a temperature......
(a) Slightly below the critical temperature
(b) Equal to critical temperature
(c) Slightly above the critical temperature
(d) None of these

Workshop Calculation Semester 3 Jan 2018

  • Read more about Workshop Calculation Semester 3 Jan 2018

 

 

Choose the correct answer.

1. Which of following is rule of indices?
a) xa ÷ xb = xa+b
b  xa  ÷ xb = xa-b
c  x6 ÷  xb= xab
d) All of these

2. If the sum of roots are 12 and product of roots is 30, then the equation will be_____
a) x2-10x+30=3
b) x²-10x-30=0
c) x²-30x+10=1
d) None of these

Pagination
  • First page « First
  • Previous page ‹ Previous
  • Page 1
  • Page 2
  • Current page 3
Subscribe to

Video

Semester-II Workshop calculation and science Paper II

Question Paper

  • Workshop Calculations Semester 1 January 2018
  • Workshop Calculations Semester 1 July 2017
  • Workshop Calculations Semester 1 July 2018
  • Workshop Calculations Semester 2 January 2018
  • Workshop Semester 2 July 2017
  • Workshop Semester 2 July 2018
  • Workshop Calculations Semester 3 January 2018
  • Workshop Calculations Semester 3 July 2017
  • Workshop Calculations Semester 3 July 2018
  • Workshop Calculations Semester 4 January 2018
  • Workshop Semester 4 July 2017
  • Workshop Calculation Semester 4 July 2018
  • Workshop Calculation Semester 4 Jan 2017
  • Workshop Calculation Semester 4 Jan 2018
  • Workshop Calculation Semester 3 July 2017
  • Workshop Calculation Semester 2 July 2018
  • Workshop Calculation Semester 1 July 2018
  • Workshop Calculation Semester 2 July 2018
  • Workshop Calculation Semester 2 July 2017
  • Monthly test (November-2015)
  • Workshop Calculation Semester 1 Jan 2018
  • Workshop Calculation & Science Sem 2 Jan 2018
  • Workshop Calculation Semester 3 July 2018
  • Workshop Calculation Semester 3 Jan 2018

Common Subject

  • Engineering Drawing
  • Employability Skills
  • Workshop Calculation Science

Directory

  • Industrial Training Institutes
  • Engineering College
  • Medical College

Electrician + Wireman + Electroplater + Electrician Power Distribution + Lift and Escalator Mechanic | ITI Fitter | ITI COPA | ITI Welder | ITI Mechanic | ITI Electronics | Agriculture + Horticulture + Floriculture | ITI Draughtsman Civil & Mech | ITI Refrigeration & Air Conditioning | ITI Turner | ITI Plumber | ITI Machinist | ITI Cosmetology | ITI Sewing | ITI Surveyor

All Syllabus

  • ITI Syllabus
  • CTS Syllabus
  • CITS Syllabus
  • Apprenticeship Training Scheme
  • Flexi MOU Syllabus
  • जन शिक्षण संस्थान Syllabus

Copyright © 2026 ITI Directory - All rights reserved

Developed and Designed by ITI Directory